Can anyone help please?

**Darren Robertson** · 17-07-2012, 12:04 PM

Hi everyone! I am wondering if anyone out there would have, or could take a decent close up pic of the two black parts, indicated by the green arrows in the picture below. The kit part itself would be of no use to me, as my Eagle is bigger than the 44" so I have to sculpt these pieces from scratch and in order to do that, I need a little help. These pieces also appear on the the shoulder pods of the Eagle I am building. My sincere thanks in advance,
Darren

**Captain Sci-Fi** · 17-07-2012, 12:59 PM

Hi Darren,

Here you go:

I have removed the image you posted as it is David's copyright, please ask him if it's OK to use it here, he is a generous, approachable chap but you had best be sure.

Good luck.

**Darren Robertson** · 17-07-2012, 05:27 PM

Thank you very much for that, Bernie! That is EXACTLY what I needed! And my apologies about the pic I used. I was obviously so wrapped up in the task at hand that I wrongly neglected to consider the copyright issues. Sorry, David!

joeb · 17-07-2012, 07:11 PM

Darren would you like the part so you can get exact measurements from it? I have extra castings I could send you. It would take a while to cross "the pond' but they're yours if you want them.

Joe

**Darren Robertson** · 17-07-2012, 07:19 PM

That is incredibly generous of you, joe and I thank you very much indeed. The measurements on the Daniel Pru D'homme prints are pretty accurate, I think, but they didn't show if the six lines were carved into the surface or embossed, which, as I am sure you now realise was.why I asked for the photo verification. I tell you this though, Joe, you are a star and when I build a 44 incher, (which I will,) I will be asking you for that very part

There are great plans in progress for this 52incher when she is complete, but I honestly cannot divulge more than that for the present. Suffice to say that I will not be keeping her when she is done.
My heartfelt thanks to you again, mate

joeb · 17-07-2012, 08:45 PM

No problem.

**Captain Sci-Fi** · 18-07-2012, 12:23 AM

Now why didn't I think of that?

I also have spares, if you need em, PM me your address.

17-07-2012, 12:04 PM	#1
Darren Robertson Astrophysics Technician Join Date: Jun 2011 Location: Truro, Cornwall, UK Posts: 314	Can anyone help please? Hi everyone! I am wondering if anyone out there would have, or could take a decent close up pic of the two black parts, indicated by the green arrows in the picture below. The kit part itself would be of no use to me, as my Eagle is bigger than the 44" so I have to sculpt these pieces from scratch and in order to do that, I need a little help. These pieces also appear on the the shoulder pods of the Eagle I am building. My sincere thanks in advance, Darren

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

17-07-2012, 12:59 PM	#2
Captain Sci-Fi Commander Join Date: Sep 2005 Location: South Glos, UK Posts: 4,341	Hi Darren, Here you go: I have removed the image you posted as it is David's copyright, please ask him if it's OK to use it here, he is a generous, approachable chap but you had best be sure. Good luck.

17-07-2012, 05:27 PM	#3
Darren Robertson Astrophysics Technician Join Date: Jun 2011 Location: Truro, Cornwall, UK Posts: 314	Thank you very much for that, Bernie! That is EXACTLY what I needed! And my apologies about the pic I used. I was obviously so wrapped up in the task at hand that I wrongly neglected to consider the copyright issues. Sorry, David!

17-07-2012, 07:11 PM	#4
joeb Astrophysics Technician Join Date: Apr 2011 Location: Buffalo, N.Y. USA Posts: 291	Darren would you like the part so you can get exact measurements from it? I have extra castings I could send you. It would take a while to cross "the pond' but they're yours if you want them. Joe

17-07-2012, 07:19 PM	#5
Darren Robertson Astrophysics Technician Join Date: Jun 2011 Location: Truro, Cornwall, UK Posts: 314	That is incredibly generous of you, joe and I thank you very much indeed. The measurements on the Daniel Pru D'homme prints are pretty accurate, I think, but they didn't show if the six lines were carved into the surface or embossed, which, as I am sure you now realise was.why I asked for the photo verification. I tell you this though, Joe, you are a star and when I build a 44 incher, (which I will,) I will be asking you for that very part There are great plans in progress for this 52incher when she is complete, but I honestly cannot divulge more than that for the present. Suffice to say that I will not be keeping her when she is done. My heartfelt thanks to you again, mate

17-07-2012, 08:45 PM	#6
joeb Astrophysics Technician Join Date: Apr 2011 Location: Buffalo, N.Y. USA Posts: 291	No problem.

18-07-2012, 12:23 AM	#7
Captain Sci-Fi Commander Join Date: Sep 2005 Location: South Glos, UK Posts: 4,341	Now why didn't I think of that? I also have spares, if you need em, PM me your address.